NDT Solutions

Radiographic testing - a form ofnon-destructive testing (NDT)- typically employs gamma or x-rays to examine manufactured parts for any flaws or defects that would otherwise go undetected with a visual inspection.

A two-part inspection solution, radiography employs ageneratorwhich, as the name implies, generates the X-rays that will pass through the sample, and adetectorthat captures the rays and the resulting image for inspection:

• Microfocus X-rayTube -In an evacuated tube electrons are emitted from a heated filament and are accelerated towards the anode by the potential difference UACC. Electrons enter through a hole in the anode into a magnetic lens which focuses the electron beam to a small spot of a few microns in diameter on the target. The target consists of a thin layer of tungsten deposited on a diamond or light metal plate which also serves as an exit window for the X-radiation (transmission tube). In the tungsten layer, the electrons are abruptly decelerated whereby X-rays are generated. Hence, the focal spot represents a very small X-ray source which enables the sharpest imaging with micrometer resolution even at high magnification. The latest nanofocus tubes achieve a detail detectability down to 200 nanometers (0.2 microns) by using multiple electron lenses. The electron beam current is controlled by the bias voltage UG via the Wehnelt electrode. A set of deflection coils aligns the electron beam with the optical axis of the lens. Since the focal spot is located at a short distance of merely 0.4 mm from the outer surface of the exit window, the cone of X-rays spreads over an angle of 170°.
• Digital Detector Array -The X-ray shadow image is converted by a scintillator foil to visible light which is directly detected by a photodiode array. The main advantages of this technique are the undistorted image as well as the high dynamics and the superior contrast resolution. The latest temperature stabilized high dynamic DXR digital detector array technology ensures brilliant live imaging with up to 30 frames per second.

Popular solutions in the industrial space areportable, field-ready generator/detector solutionssuch as those used in the inspection ofOil & Gaspipelines, and the larger,laboratory and/or production floor X-ray inspection and computed tomography (CT) systemsas seen in theAutomotive,Aerospace,andElectronics Manufacturingindustries, which offer a greater degree of precision.

Computed Tomographyis another form ofnon-destructive testing (NDT)使用数以百计的x射线图像来创建三个-dimensional models of the internal and external structures within a scanned sample.

有three types of scanners associated with industrial CT scanning, cone-beam, line-beam, and fast gantry-based helix:

• Cone-beam -Generating volumetric data using industrial cone beam CT starts with the acquisition of a series of two-dimensional X-ray images while progressively rotating the sample step by step through a full 360° rotation. These projections contain information on the position and density of absorbing object features within the sample. This accumulation of data is then used for the numerical reconstruction of the volumetric data.
• Line-beam -To ensure high CT data quality with reduced scattering artifacts at high X-ray energy, collimated line detector arrays are being used for CT data acquisition. For each slice, a set of X-ray line profiles is acquired while progressively rotating the sample step by step through a full 360° rotation. By vertically shifting the sample through the fan beam and repeating the procedure, a set of slices is compiled to obtain a representation of the volume.
• Fast gantry-based helix CT -At high-speed helix CT based on medical computed tomography technology, a gantry with an X-ray tube and corresponding line detector rotates around the workpiece being forwarded on a linear belt manipulator. To ensure the required image quality with short measuring times and low scattering artifacts, a highly sensitive multiline detector is being used. A typical casting workpiece is being scanned within 10-90 seconds. The numerical volume reconstruction starts automatically, even 3D evaluation tasks like automated defect recognition (3D ADR) including good/fail decisions can be performed fully automated.

Typical tasks for which CT is suited includeflaw detection, metrology, failure analysis, and the like.

One of the key benefits of modern industrial CT solutions is the ability to employpart-to-part or part-to-CAD comparisonwhere two models are overlayed and/or compared: one being the CAD file or a reference scan from a known good sample, and the other being the production sample being scanned. This level of detail and reference greatly enhances the rate of flaw detection and can be used for reverse-engineering and geometric dimensioning.

Ultrasonic Testing (UT)is another form ofnon-destructive testing (NDT)that employs ultrasonic waves which are transmitted into materials and samples to detect flaws such as cracks and tears and to measure thickness - an important measurement for welds, seams, and corrosion prevention in pipelines.

Automated Ultrasonic Testing (AUT)refers to the use of UT technologies where the transducers and receivers are driven by a mechanical system that ensures consistent measurements as well as the ability to repeat the test over and over. One popular application of AUT is in pipeline inspection, where a system can be clamped around the outside of a pipe and then walked or piloted down the length of the pipe collecting data along the way for analysis.

Phased Array Ultrasonic Testing (PAUT)is a UT solution that employs a series of phased array probes that allow for the beam to be focused and swept without physically moving the probe - which allows for scanning in tighter locations where traditional single-element systems may not fit, or where motion is otherwise limited, thus resulting in a smaller scan size. PAUT is one of the best solutions for defect detection where time is of the essence, and scanner mobility is impaired or impossible while simultaneously increasing your Probability of Detection (POD).

Visual Inspection, the first and oldest form ofnon-destructive testing (NDT), is that which is done with the naked eye as the primary scanning “tool” if you will.Modern visual inspection solutions augment the technician's natural abilitiesby allowing them to inspect hard to reach or hard to see locations thanks to video borescopes, rigid and flexible borescopes, and even remotely operated vehicles (ROVs).

Many of these modern solutions also offerenhanced lighting, contrast, and other image transformsthat aid in the detection of flaws, thus enhancing the technician's vision while still relying on their expertise to make the determination of what is flawed and what is not.

Eddy Current Testing (ECT)is a form of non-destructive testing (NDT) that employs electromagnetic inductionto detect and define flaws in conductive materials.ECT is a great solution for checking surface and subsurface (i.e. underneath a coat of paint) conditions.

ECT transducers, at their core, are comprised of a coil of wire (i.e. an induction coil) and an alternating current which together forma magnetic field.When this coil is introduced to conductive materials, any opposing currents will be induced into the material andwill be visible as eddy currents.

Any defect in the target material will manifest itself as a disruption in the eddy currents, which can then bemeasured by way of their changing impedance. It is this sort of non-visual confirmation of surface and subsurface defects thatmakes ECT perfect for weld inspection, fastener hole inspection, tube inspection, heat treatment verification, and even metal grade sorting.

磁粉探伤(MPI)is a form of non-destructive testing (NDT) that, as the name implies, employs a magnetic field to detect surface and subsurface irregularities in ferromagnetic materials.

When a magnetic field is applied to the target sample, the piece can then be magnetized and any resultant irregularities in the material can bedetected by the application of ferrous particles or ferrofluidand checking for areas where larger concentrations of the ferrous materials have gathered, thus indicating a deformity in the material.

Acoustic Emission Testing (AET),another form of non-destructive testing (NDT) relies on theuse and measurement of acoustic waves when passed through a solid. What makes AET different from conventional ultrasonic testing (UT) and limited to a very specific sort of defect, is that the waves being detected are actually produced by the target material during a failure or stress event, and not from an outside generation source.

Due to this ability, AET is often used todetect defects during the manufacturing process, such as a crack during welding of a pipeline that may go undetected.

Liquid Penetrant Testing (LPT)also known asDye Penetrant Inspection (DPI)is another form of non-destructive testing that is used to detect surface defects in non-porous materialsrequires the application of a penetrating liquid, usually an emulsifier,which is then exposed to a developer把渗透液体从苏吗rface defect thus amplifying the presence of a defect through a concentration in the appearance of the penetrating liquid on the surface of the sample.

While inexpensive and relatively simple to deploy, LPT requires a clean surface, protective clothing, and proper ventilation, andresults in a detection level only slightly higher than visual, with proper LPT training of the technician. One should also consider what methods are used in the cleaning of your target materials prior to LPT assome surface prep methods can interfere with the testthus skewing your results.

Leak Testingis another simple form of non-destructive testing (NDT) that does just what the name implies: it tests a given manufactured partto make sure fluids or gases aren’t escaping from any unintended paths.

有several forms of Leak Testingfrom total submersion (i.e. the “bubble test”) to helium leak testing, pressure decay, vacuum decay, flow monitoring, and thermography.

This method of testing iswidely used across multiple industrieswhere leaks could be a problem, from automotive, oil & gas, to consumer packaged goods (CPG), medical, and waterproof electronics.